Virtual stick commands occasionally unresponsive on Mavic 2 Pro

已完成

关注

Joe Waldron

• 2023年07月18日 15:48

We are having sporadic virtual stick command issues with MSDK V4.16.4 when used with aircraft firmware 01.00.0670 and RC firmware 01.00.0640. Aircraft is Mavic 2 Pro and we are using in combination with Odroid N2. The issue is that the aircraft sporadically fails to respond to pitch or roll commands after auto takeoff has completed, but throttle command does appear to remain responsive. All prerequisite calls are made and are reported successful before we start sending the virtual stick commands, and we know there is no problem with our workflow because 99% of the time, the drone is responsive to all of our virtual stick commands. It is an indoor use case, so no/limited access to GPS. RC flight mode switch is always in 'P' mode and we always get the callback to say that the stick commands are successful, but the drone simply doesn't respond. Are you able to support with this issue please?

0

• 

  DJI Developer Support

  • 2023年07月19日 07:38

  What is the frequency of occurrence of this issue? Are there any obstacles near the aircraft when this issue occurs?

  0

  评论操作 固定链接
• 

  Joe Waldron

  • 2023年07月19日 08:30

  Thanks a lot for your reply.

  It's completely unpredictable when it could happen. We could conduct 10 flights without any problems, then it could occur 1 in every 3 or 4 flights.

  There are obstacles within the environment (generally 70 to 100cm infront of the drone), but as part of our workflow, we deactivate obstacle avoidance in any case. By your question, I'm assuming you disable virtual sticks in the event an obstacle is detected. Is that right?

  One thing I was wondering is how the virtual sticks function if/when the aircraft automatically switches from OPTI to ATTI mode in the event that vision system is having difficulties in the environment. Could you explain that for me please?

  0

  评论操作 固定链接
• 

  DJI Developer Support

  • 2023年07月19日 13:40

  I'm assuming you disable virtual sticks in the event an obstacle is detected. Is that right? -->Yes, I think it could be related to obstacle avoidance. One thing I was wondering is how the virtual sticks function if/when the aircraft automatically switches from OPTI to ATTI mode in the event that vision system is having difficulties in the environment. Could you explain that for me please? --> Aircraft will have limited flight altitude in environments where visual systems fail. I did not find any explanation for the limitation of flight distance. If there is a method that can consistently reproduce this phenomenon, it may be better for analysis. Another method is to analyze the aircraft's state at that time through flight control logs.

  0

  评论操作 固定链接
• 

  Joe Waldron

  • 2023年07月19日 14:43

  Thanks again for your reply.

  But if we send the call to disable active obstacle avoidance and receive the success callback, in theory the sensors should be disabled, right? With that being the case, I don't understand how obstacle avoidance could prevent the drone's response to our virtual stick commands. Perhaps you could shed some light on how this could be possible?

  0

  评论操作 固定链接
• 

  DJI Developer Support

  • 2023年07月20日 08:24

  But if we send the call to disable active obstacle avoidance and receive the success callback, in theory the sensors should be disabled, right? -->Yes, if you have already disabled obstacle avoidance, you can eliminate the impact it may have caused. I would like to know if you are aware of whether the remote control can perform actions such as controlling the aircraft's forward, backward, and left-right movements when the virtual joystick is unable to do so. Could you provide me with more information on this? Alternatively, provide me with a copy of the flight control system log of the aircraft at the time of this problem so that I can confirm the status of the aircraft.

  0

  评论操作 固定链接

请先登录再写评论。